Відео

Are these still being made? I would love a case like this

My switch hole has 2 lifted pcb solder holes, any tips or am I doomed?

Bro, help please. In My case when do this, go to inverte, like f5 dont work, and I sold f6 (work) with f5 (dont work), so, when I click f5, go to f6

Obrigado amigo, do Brasil

What a nice review there, so informative. Thanks!

The key i needed to work worked, but the other keys like alt keys both (L,R) is now nit working ang the windows key turned into alt key help pls

I was trying to open the back of my keyboard without realizing that there are 10 screws holding the back in place. I was forcing my way in and damaged the board near LCTRL key. LCTRL key was not responding and I thought I needed to buy a new keyboard but I took a wire and bridged the pin from LCTRL all the way to F12 (had to look for it assuming it's different on every keyboard) and just like that it worked. Thank you sir.

my pi3+ barely runs 480p

Just fixed my cougar using your video, man thanks so much! PD: if it helps for someone, be sure you are attaching the switch to GND of a switch with the same GND working

my row of left shift to /?key is not working where do i start the bridge?

Can I get the configuration command for the relay switch. The configuration link you drooped was that of alarm setting.

after connecting them together does the f1 key still work?

how well does it get stuck on grime off? the keycaps that I am using haven't been cleaned in years and want to make them clean before getting a new keyboard.

Thank you so much! I am a total amateur and I was lost, but thanks to you, I know how to install stabilisers now. I like how you make everything simple and easy to understand..the hotel and ground floor analogy is brilliant =)

Just fried my Pi. dont ever connect the 5V on the relay board to your Pi. I now use the 5V and GND pin on the relay board to power my arduino, which is receiving serial commands from another Pi I have laying around. The downside is you gotta code twice - use AI to generate that 😅 It was my own fault, I should've tested the power pins on the relay board.

Great video. It doesn't help me as I'm using a B+, but it's still good to learn from.

Hey,sir it can only solve problems for certain models, right? Because I tried to do spacebar and alt and yes it worked and I tried to do another switch. But after that I connect ctrl with fn, when I check it it doesn't work. But the N button came on instead. thx

Ive soldered my spacebar key to my B key and all its doing is just firing spacebar and do you know how to fix this because ive been struggling to understand why its doing this. If you have any suggestions please lmk bc ive been trying to fix my keyboard for months.

When I use the socket left or right from my broken switch the switch is working again but it triggers the action from where the bridge is coming… what I am doing wrong here? Nice Video by the way!

Brother, when i bridge the pin, its picking up the key which i have bridged from. And that key doesn't work. What should I do?

Thank you, I needed to know if this thing was configurable befor ei purchased one.

Thank you man, you were the only one on the whole internet that helped me with my keyboard, you are a legend

Thanks. I'm watching this in 2024 and it's kind of content I wish I could see more (soldering camera kicks ass!)

Can I ask 2 questions? can I use copper wire without rubber coating? in this case is it better to position it behind the PCB like you did, or in the other side or does it not matter? (to avoid counter-circuits)

youtube.com/@Raspberrypi_CNC_Controller?si=Mxbt5ZNTwRL6ovxx

Nice, how did you manage to run all of them simultaneously with python? I had to use multiprocess, check this out if you still work with steppers. ua-cam.com/video/WprF3Dy7BbE/v-deo.html

I tried this on my left arrow to my down arrow, but now it triggers the down arrow. How should I fix this?

Could you tell me what material this cable should be made of? Thank you!

In order for the relay board to work for a Raspberry Pi 4 you must ensure the inputs are active HIGH. Most boards out there are active or trigger LOW. If you have a active LOW board you will need to place a Darlington sink drive ahead of the relay board inputs. Use something like a ULN2803. You will need two of them, cost about $1.25 each.

Man how can i fix my column pin its attached to the transistor i think maybe on the top for column, it is kinda broken how can i fix it

Thanks for this video! Referred to this because I lifted a pad when desoldering, and I'm more of a visual person. Much love, and happy New Year!

My F rows of mechanical keyboards don't work, can I connect a cable from the numbers row to F row and it'd work?

the bridge work but some time my keyboard key is glitching, amy suggestion?

Bro I bridged a pad to a diode that was not working, it was the letter "C" I noticed that after this it was fixed but now I am not able to press the letter C and B at the same time. Any way on fixing this back to normal?

pete you're an absolute legend. saved me $70 on a new pcb

0 to 35mph in 3hrs. 😅

can i use this like in my work, i work on chicken houses all over the place, can i take this or say the 8 channel and hook it to my stuff and control it from anywhere in the world and the pi has internet access? how hard would it for a newbie that's not that smart and just getting into this...

Thnx

You saved my keyboard from my clumsyness and inexperience!

I have the SteelSeries Apex Pro and the two stabs came out making it unfixable since I don't have the guts to disassemble the entire keyboard 😭

What about if i fucked both of the pins on escape key, do i need to bridge both pins to the next keys, like collom and row just, like next keys

THANK YOU for showing fully how to do shift key type stabilizers, direction and all

I was meaning to do this myself on my raspberry pi, but it's nice to have everything there so as a first project I can play around with something already done. I wrote an android app that didn't work to do this. I'm pretty sure I had the logic right, but there must have been something wrong somewhere along the way. I've found a nice app that does this very well now, so I've been able to resurrect my atomic watch - same as they one you displayed. The app is : "radio watch synch" on android, and I believe it's on ios as well.

Thank You, I had a keyboard which i thought was unrepairable but I found your video and after watching I managed to fix it, Amazing. Thank you again.

hi thanks for this video. Can I ask if it's still necessary to solder if the board is hotswap? Am I able to bridge using a wire without soldering?

Thanks, nice vid

Thank you so much!!!!!!!!!! you safe my lifeeee. thanksssssss

hey does anyone know where i can download the driver to change the colors for this keyboard?

Thank you!! FYI for anyone who is looking for electrical wire like me now, you want 28 AWG.